Tablet

Manufacturer

LUBE INDUSTRIES Srl Via dell’industria, 4 - Treia (MC)

Product Name

Kitchen cabinets, TABLET model.

Caution

This product data sheet complies with the specifications set out by Italian Legislative Decree no. 206 dated 6th September 2005 "Consumer Code".

Materials Used - TABLET Melamine

Doors and deep drawer fronts

Door formed of an 18 mm thick chipboard panel support (class E1), melamine-faced opaque or semi-gloss wood effect finish with vertical grain, opaque cement effect finish, super opaque solid colour finish with back in the same colour. Edged on 4 sides with laser edging. The doors with super opaque finish may have edging in the same colour or in plywood.

Drawer fronts

Same as doors.

Materials Used - TABLET UV Lacquered

Doors and deep drawer fronts

Door formed of an 18 mm thick, medium-density wood fibre panel support (class E1), ABS edging with opaque coloured interior and UV glossy lacquered exterior.

Drawer fronts

Same as doors.

Materials Used - TABLET Glass

Doors and deep drawer fronts

Door formed of two, 18 mm thick MDF uprights , melamine-faced wood effect, and two opaque powder-coated aluminium cross-beams, without handle grip and with 4 mm thick screen printed, satin-finish and tempered fluted glass.

Glass doors and deep drawer fronts (aluminium frame)

The frame is an extruded 6060 aluminium profile subjected to chemical oxidation, brushed and with “brill” finish on which a 4 mm thick, satin-finish or “titanium” finish tempered and bronzed glass pane is mounted.

Handles – BRIDGE VERSION

In aluminium or zamak alloy with galvanic bath in satin nickel, chrome, opaque satin, burnished, opaque black finishes, in marine plywood and front finish in laminate in the same opaque colours as the super opaque doors.

Finger rails - NECK VERSION

In aluminium with "L"-shaped section, brushed finishes in the following colours: stained titanium and glossy aluminium; opaque powder-coated in the following colours: total white, warm white, beaver, smoke grey, Bromine grey, lead grey, black, cornflower blue, amber, pink quartz, Tuscan red and sienna.

Handles – HEAD VERSION

Anodised aluminium profile with brill and titanium finish, recessed on the horizontal side

Components Description

Drawer structure and shelves

Consisting of 18 mm thick melamine-faced chipboard panels in accordance with the US EPA TSCA Title VI standard (with very low formaldehyde emission).
The shelves are 18 mm thick and equipped with built-in shelf supports with locking device. They can also be made of tempered glass (6 mm thick), grounded on the edges.

Edge

Edge in ABS or Polypropylene (PP) glued with thermosetting polyurethane glues 1 mm thick on the front parts of the unit sides and shelves and 0.5 mm thick on the lower and upper parts of the unit sides and on the sides and rear part of the internal shelves. Made of paper for the non-visible parts of furniture (back).

Backs

Consisting of 2.8 mm thick high-density fibre panels compliant with E1 and US EPA TSCA Title VI for formaldehyde emissions, wall units with polypropylene veneers and painted bases and columns.

Worktop

Laminate worktop: 38 or 58 mm thick water-repellent wood particle board coated with high pressure laminate (HPL). For worktops in other materials, please refer to the "Useful information" section.

Sink

In sheet 18/10 stainless steel made using a single-casting or electrically welded tubs, with a smooth or "embossed" finish. For sinks in other materials, please refer to the "Useful information" section.

Brackets

Faced bracket: melamine faced wood particle board panel (class E1); ABS edging.
Veneered bracket: wood particle board panel (class E1) veneered with "slices" of wood (which vary depending on the model) and lacquered using acrylic/polyurethane products.

Frames

In pine wood or MDF (class E1) veneered with "slices" of wood (which vary depending on the model); acrylic/polyurethane lacquering.

Sink unit base coating

In chequered aluminium or lacquered plastic to protect the sink unit from water seepage.

Feet

In knock-resistant plastic material (PVC) and height-adjustable, these are screwed to the bottom of the cabinet using special bushing, without requiring any drilling in the lower part of the casing (thus completely avoiding the creation of areas in which dirt may accumulate or through which water could leak into the base and sink cabinets).
They are also available in aluminium and can be adjusted and mounted on a special base structure (also made using an aluminium profile).

Skirting

These elements may be made using anodised or lacquered aluminium, or PVC coated with decorative melamine foil, and have a rubber seal at the top and bottom.

Regrigerator unit base

In rigid plastic material (PVC), drilled in the centre to allow any leaking water to escape and to protect the main cabinet column.

Backsplash for worktops

In aluminium or rigid knock-resistant PVC with laminate decoration.

Hinges

In sheet steel and zamak alloy, copper-plated and nickel-plated for resistance to corrosion; adjustable in three directions.

Drawers and total extraction deep drawers (internal structure)

The structure may consist of a 16 mm thick wood particle base (extremely low formaldehyde emission) faced in grey laminate with side and back panels in galvanised and lacquered sheet steel for protection against corrosion. Alternatively the structure can be made entirely of solid ash and plywood; sliding takes place by means of total extraction runners with a grooved system for anti-detachment locking and automatic closure which is activated in the final 4 cm. The soft-close system (blu-motion) is also supplied as standard.

Plate draining racks and baskets

In electrically welded metal wire; they may be plasticised with polymer resin, nickel-plated or chrome-plated and coated with a transparent plastic sheath (Crominox finish).

Tables

Top: may be a wood particle panel (class E1) coated with HPL plastic laminate (see laminate worktop) or veneered with "slices" of wood and lacquered with water-based, polyurethane or acrylic shades, or it may be made using glass, granite or natural stone.
Borders and base structure: these may be made using metal or plywood panels, faced or veneered with "slices" of wood (these vary depending on the model).
Legs: these may be made using metal or solid wood; lacquering is carried out using acrylic/polyurethane products.

Chairs and stools

Structure: this may be in tubular metal lacquered with thermosetting powders, or in solid wood lacquered using water-based (impregnating) and acrylic/polyurethane products (base).
Seat and Backrest: these may be made using synthetic material (methacrylate), solid wood, plywood, upholstered fabric or simulated wicker.

Note: each type of chair or table is identified at the site of purchase by the relevant adhesive label on the packaging.

For further information, please check the user and maintenance manual provided by GRUPPO LUBE.